sensing IMX390 相机接入FPD-LINK3-2RX驱动

veye_xumm — Fri, 08 Dec 2023 10:24:58 GMT

@kevin2008 生成video节点只能表明i2c通了。看你的截图，像是mipi接收部分的配置不对。

Yocto with Fpdlink Camera on Jetson Nano

veye_xumm — Fri, 22 Sep 2023 08:49:19 GMT

@red Hi, I didn't understand your meaning. Yocot is a project management tool, right? The demo we provided is just on the wiki and is not integrated with Yocot.

tda4支持sc132

yukang.zhong — Thu, 31 Aug 2023 03:32:50 GMT

@yukang-zhong 你好，现在已经lock上了，但是显示camera没有数据发出 i2c命令读camera也没有数据，显示不可读，请问一下需要怎样设置camera,camera才有数据出来我们的连接如下ds90ub954对应的部分，我们是ds90ub962 #/-------------------\ /----------------------\ /--------------------\ /------------------ #| MIPI CSI RECEIVER | | FPDLINK DESERIALIZER | | FPDLINK SERIALIZER | | MIPI CSI CAMERA | #+-------------------+ CSI +----------------------+ +--------------------+ CSI +------------------+ #| | <----- | | Coax | | <----- | | #| Raspberry Pi (4) | GPIO | fpdlink2raspi | <----> | piCam2fpdlink | GPIO | Raspberry Pi | #| Jetson Nano | <----> | PCB | | PCB | <----> | Camera Module v2 | #| ... | I2C | ds90ub954 | | ds90ub953 | I2C | | #| | <----> | | | | <----> | | #-------------------/ ----------------------/ --------------------/ ------------------/ ID ADDR (7BIT) 0x30 0x18 0x3B(VEYE CAMERA) ID ADDR (8BIT) 0x60 0x30 0x76(VEYE CAMERA) ALIAS ADDR (7BIT) NA 0x19 0x3B(VEYE CAMERA) ALIAS ADDR (8BIT) NA 0x32 0x76(VEYE CAMERA) i2cdump -f -y 7 0x18 No size specified (using byte-data access) 0 1 2 3 4 5 6 7 8 9 a b c d e f 0123456789abcdef 00: 30 00 73 48 00 03 43 fa fe 1e 10 7f 7f d2 2d 00 0.sH.?C???????-. 10: 00 00 00 00 00 20 18 3c 80 62 62 62 00 00 00 00 ..... ?

NVIDIA Jetson Agx Orin 64Gb - IMX327s fpdlink camera software solution

red — Wed, 12 Jul 2023 12:39:33 GMT

@veye_xumm Thank You . I try today .

fpdlink3 camera树莓派连接不上

veye_xumm — Sat, 04 Mar 2023 08:05:18 GMT

@sakura 不是的，摄像机的版本。你用的什么型号的摄像机？

/dev/video0 not found and in dmesg there is no "probing v4l2 sensor\n"

veye_xumm — Fri, 03 Feb 2023 18:03:32 GMT

@chjchoi I think this place means that the 954 chip is not detected properly on the i2c.

How to change cssc132 and ds90ub954 loading sequence?

veye_xumm — Thu, 15 Dec 2022 08:56:47 GMT

@dmmoskalev Great!

I don't know why fpdlink 3 init stops with the message no acknowledge from address 0x30...

chjchoi — Wed, 14 Dec 2022 08:34:08 GMT

Jetson TX2 (JetPack 4.4)+ FPD LINK III for Jetson of VeYe's After modifying ADP-N3 according to ADP-N2 pin map...

TX2 board does not boot after installing ADP-N2.

veye_xumm — Wed, 07 Dec 2022 04:01:43 GMT

@chjchoi I tried to send you an email , but it bounced back. Please confirm this email address.

FPD-LINK3-2RX need a 12V DC power.

veye_xumm — Fri, 16 Sep 2022 11:47:58 GMT

@laks said in FPD-LINK3-2RX need a 12V DC power.: Can u provide specification for 12V DC supply. Also if there is any specific part number to buy. Using the most common and ordinary 12V DC power adapter is fine.

急需关于FPD-LINKIII对于Orin的适配

veye_xumm — Sun, 11 Sep 2022 14:33:00 GMT

@ledzhongzi 不客气

Is there 4 camera system for CS-FPD-CAM Series?

veye_xumm — Fri, 25 Feb 2022 06:27:29 GMT

@sophiajackson22 Thank you for the information, I will keep an eye on it.

vEye Camera with own CarrierBoard

veye_xumm — Tue, 14 Sep 2021 12:03:32 GMT

@g-towboat Our solutions are 953 and 954 and the source code of the driver is provided. You can refer to this source code to support 964. Now fpdlink products have been suspended due to chip out of stock, sorry.

Sensor crop mode

g-towboat — Thu, 10 Jun 2021 11:54:20 GMT

@veye_xumm ok i am understand, just these three formats thank you

关于发热问题

veye_xumm — Thu, 13 May 2021 10:10:46 GMT

@wqeeqweqwwccsd 已经收到了，同事在处理中。下周初会发回给你。

修改FPS问题

veye_xumm — Thu, 06 May 2021 06:39:35 GMT

@wqeeqweqwwccsd said in 修改FPS问题: ，请问这样可行吗？不可行，sync模式不支持的。会自动跳回默认帧率。

sync问题

veye_xumm — Sat, 24 Apr 2021 14:04:56 GMT

@wqeeqweqwwccsd 你这种测试方法是极为模糊和不确切的。请参考我上一个帖子发给你的链接。

cs_mini_i2c.sh问题

veye_xumm — Fri, 23 Apr 2021 07:38:57 GMT

@wqeeqweqwwccsd 当然是支持的。你可以看这篇文章 6.3 6.4两个部分。 http://wiki.veye.cc/index.php/FPD_LINK_III_for_Jetson/zh 其中，6.4 xavier的典型案例就有实现了同一颗954连接的两路视频的同步。

How to change FPD-Link 3 Operating Mode (CSI-2 mode -> raw mode)

veye_xumm — Tue, 20 Apr 2021 04:19:50 GMT

@yongjin I don't know what your current state of knowledge is. If you don't understand i2C, you don't understand fpdlink, you don't understand registers. I think you should first learn the basics and be able to understand the information and code we provide now, and then proceed to your next work. Good luck.

如何同时使用四路摄像头

veye_xumm — Mon, 19 Apr 2021 02:54:41 GMT

@robot nano现在只能支持2个摄像头。核心的限制因素是： nano这颗cpu，不支持mipi的虚拟通道。也就是说两路视频融合到一个mipi通路中进入cpu，这个功能，nano是支持不了的。

在向自己的Image中添加驱动的过程中遇到了error during i2c read probe (-121)

veye_xumm — Sat, 17 Apr 2021 09:20:19 GMT

@robot ok

请问如何初始化？

veye_xumm — Tue, 13 Apr 2021 08:48:36 GMT

@wqeeqweqwwccsd 可以

关于FPD-link3的同步问题

veye_xumm — Mon, 12 Apr 2021 08:51:48 GMT

@wqeeqweqwwccsd 你好，具体请参考下面这篇文章。连接方法在6.4 http://wiki.veye.cc/index.php/FPD_LINK_III_for_Jetson/zh#CS-FPD-CAM-IMX307.E7.9A.84.E5.90.8C.E6.AD.A5.E6.A8.A1.E5.BC.8F.EF.BC.8C.E8.BF.9E.E6.8E.A5.E5.88.B0Jetson_AGX_Xavier

csimx307-fpdlink

veye_xumm — Wed, 24 Mar 2021 12:40:51 GMT

@wqeeqweqwwccsd 摄像头你采用同步模式了吗？感觉像是从摄像头没有得到同步信号。

Camera hotplug

veye_xumm — Mon, 22 Mar 2021 13:35:43 GMT

@g-towboat right.

FPD LINK III Camera