Hi @veye_xumm, I didn't say that this is issue, this parameter needs to be changed only in case video recording of the night sky (meteor detection)

From issues what I noticed:

• can't save fps - always 60 after power on

• Sometimes saved parameters resets to default (noticed when set metime to 33333 but forgot set fps 30 before) and manual expmode switched back to auto

@veye_xumm found what was wrong,
high level of noise produced gamma_index = 1 (default value), other looks good.

@veye_xumm yes, you are right, I checked image in 25 and 26 dB - and it is switching.

Probably I used high digital gain (because brightness low than from IMX462 in same gain value) and it produces high level of noise.

About denoise, in IMX462 I'm using 0x02, but not sure what is MIDDLE value, because in IMX662 denoise_strength_3D with 128 produces different picture and I decreased to 40 to have something similar

0x02	NR 2D Mode = OFF; NR 3D Mode = MIDDLE

Will test couple nights. Thank you.

@sheko
As I see your standard camera parameters are: 1080x1280 120fps
And as it configured in python script for first step try:

cap = cv2.VideoCapture('v4l2src device=/dev/video0')

if still failing try with passing parameters to gstreamer:

cap = cv2.VideoCapture('v4l2src device=/dev/video0 ! video/x-raw,format=UYVY, width=1080, height=1280,framerate=120/1 ! videoconvert ! video/x-raw,format=GRAY8 ! appsink sync=1')

or from command line to check if gstreamer works without python

gst-launch-1.0 v4l2src device=/dev/video0 ! video/x-raw,format=UYVY, width=1080, height=1280,framerate=120/1 ! videoconvert ! video/x-raw,format=GRAY8 ! appsink sync=1

if still failing try RAW8 format

gst-launch-1.0 v4l2src device=/dev/video0 ! video/x-raw,format=RAW8, width=1080, height=1280,framerate=120/1 ! appsink sync=1

if still failing, can't help, I don't have this sensor.

@veye_xumm happy holidays!
Yes, I tried manual and auto gain/expmode and it works as expected.

For meteors detection I don't need use denoise3d (or use small value ), as it blurs fast moving objects, but without it the image very noisy, which is probably related to HCG and LCG modes of sensor (as it was for my IMX462M camera and you provided custom firmware with enabled HCG), and it is working perfectly on VEYE IMX462 cameras.

For now it has quality of usual IP camera with same sensor (with denoise3d for night sky), will wait, probably it will be improved in future.
Thank you!

@sheko please update pipeline with your camera parameters (width, height, framerate). I just copied mine.

@sheko
This is pipeline which need place to openCV instead:

cap = cv2.VideoCapture('/dev/video0')

to run it from command line you need use gstreamer, try :

gst-launch-1.0 v4l2src device=/dev/video0 ! video/x-raw,format=UYVY, width=1920, height=1080,framerate=30/1 ! videoconvert ! video/x-raw,format=GRAY8 ! appsink sync=1

Hi @veye_xumm, sorry for confusion, in previous time you guided me to install custom libcamera for veye_mvcam driver and seems like this step is outdated (but I'm still using libcamera).

@Sheko try another pipeline in openCV:

v4l2src device=/dev/video0 ! video/x-raw,format=UYVY, width=1920, height=1080,framerate=30/1 ! videoconvert ! video/x-raw,format=GRAY8 ! appsink sync=1

Hi @sheko, I had same problem with RPi 5, did you build and install libcamera from veye github repository? For some reason it has config json file only for RPi 4.

First step try run it with uncalibrated json :

rpicam-still --tuning-file /usr/local/share/libcamera/ipa/rpi/pisp/data/uncalibrated.json -t 0

Path may be different, if failed to load json file - try to find valid path.

if video opened - we need just put to same folder mvcam_mono.json (or add to libcamera source code, update meson.build and rebuild + reinstall )

and check if rpicam-hello or rpicam-still works without tuning file

I attached my current config (rename it to json) but it adopted for night sky and you need fix in json file section : exposure_modes . normal, copy it for example from se327m12.json
mvcam_mono.txt

Hi @veye_xumm, I'm already on the latest version of firmware:

$ ./gx_mipi_i2c.sh -r version -b 4
Read version is C 01.14 and L 01.11

Anyway it is not critical issue for me.
I'm trying this new GX-MIPI-IMX662 as improved version of VEYE-MIPI-IMX462 for meteors detection and can't configure with same way.

If turn off denoise_strength_3D the video image is very noisy and as in gx_mipi_i2c no feature to read sensor registers, can I ask to you confirm that:
In low light environment ISP enables HCG mode (register FDG_SEL0 0x3030 sets to 0x01) ?

Maybe you have other recommendations like for IMX462 in this post :
VEYE-MIPI-IMX462 - manual gain not consistent