VEYE-MIPI-IMX462 - manual gain not consistent

[milank]

@milank

the same procedure runs on many installations using the IP camera without strange phenomenons like on the picture.
This is the attempt to replace them by a MIPI camera.

[veye_xumm]

@milank Can you tell us about your curve generation method?

[milank]

@veye_xumm
for this, please see:
https://github.com/CroatianMeteorNetwork/RMS/blob/master/Utils/PlotFieldsums.py

[veye_xumm]

@milank

I have provided a script in the attachment which can read the sensor registers.
Can you please add a monitoring program in your system to monitor the following registers of the sensor: 0x14, 0x20, 0x21, 0x22, and 0x09.

The usage of the script is: ./veye_inner.sh -r -f sns_reg -p1 [sns_reg_addr].

Especially pay attention to whether the registers of the sensor have changed when a sudden change in brightness is detected.

veye_inner.sh.txt

[milank]

@veye_xumm

fine, understood, now it is running in the background for spoken registers.
I will come back with the results once I see the spike again.

[milank]

@milank
Another change has been detected last night, around 20:44:25 UTC.
Unfortunatelly, no change detected in spoken registers.
The reading interval was set to 5 seconds.
I am also attaching two full BMP images just before/after the change of brightness. 

03/15/2023 20:44:11 reg addr 0x14 val is 0x53
03/15/2023 20:44:11 reg addr 0x20 val is 0x1
03/15/2023 20:44:11 reg addr 0x21 val is 0x0
03/15/2023 20:44:11 reg addr 0x22 val is 0x0
03/15/2023 20:44:12 reg addr 0x9 val is 0x11
03/15/2023 20:44:17 reg addr 0x14 val is 0x53
03/15/2023 20:44:17 reg addr 0x20 val is 0x1
03/15/2023 20:44:18 reg addr 0x21 val is 0x0
03/15/2023 20:44:18 reg addr 0x22 val is 0x0
03/15/2023 20:44:18 reg addr 0x9 val is 0x11
03/15/2023 20:44:24 reg addr 0x14 val is 0x53
03/15/2023 20:44:24 reg addr 0x20 val is 0x1
03/15/2023 20:44:24 reg addr 0x21 val is 0x0
03/15/2023 20:44:25 reg addr 0x22 val is 0x0
03/15/2023 20:44:25 reg addr 0x9 val is 0x11
03/15/2023 20:44:30 reg addr 0x14 val is 0x53
03/15/2023 20:44:30 reg addr 0x20 val is 0x1
03/15/2023 20:44:31 reg addr 0x21 val is 0x0
03/15/2023 20:44:31 reg addr 0x22 val is 0x0
03/15/2023 20:44:31 reg addr 0x9 val is 0x11
03/15/2023 20:44:36 reg addr 0x14 val is 0x53
03/15/2023 20:44:37 reg addr 0x20 val is 0x1
03/15/2023 20:44:37 reg addr 0x21 val is 0x0
03/15/2023 20:44:37 reg addr 0x22 val is 0x0
03/15/2023 20:44:38 reg addr 0x9 val is 0x11
03/15/2023 20:44:43 reg addr 0x14 val is 0x53
03/15/2023 20:44:43 reg addr 0x20 val is 0x1
03/15/2023 20:44:43 reg addr 0x21 val is 0x0
03/15/2023 20:44:44 reg addr 0x22 val is 0x0
03/15/2023 20:44:44 reg addr 0x9 val is 0x11

[milank]

@milank

[veye_xumm]

@milank
Hi, we guess it might have something to do with an "extra" gain in ISP, which is a bug in new_expmode that doesn't completely turn off the automatic control of the image in ISP.
You can try to configure it with this command and then test it again

. /veye_mipi_i2c.sh -w -f brightness -p10

BTW,since you are using the camera to capture the starry sky, it is recommended that you run the following script to turn off the automatic bad point correction.

./i2c_write 10 0x3b 0x0007 0xFE
./i2c_write 10 0x3b 0x0010 0xDB
./i2c_write 10 0x3b 0x0011 0x9F
./i2c_write 10 0x3b 0x0012 0x00
./i2c_write 10 0x3b 0x0013 0x00
./i2c_read 10 0x3b 0x0014 1

[milank]

@veye_xumm
fine, thank you, I will test, my init script now looks like:

./veye_mipi_i2c.sh -w -f new_expmode -p1 1
sleep 1
./veye_mipi_i2c.sh -w -f new_mshutter -p1 40000 # fixed 40 ms
sleep 1
./veye_mipi_i2c.sh -w -f new_mgain -p1 23 # between 20 and 25
sleep 1
./veye_mipi_i2c.sh -w -f brightness -p1 0
sleep 1

special code for sky imaging, to turn automatic bad point correction off

./i2c_write 10 0x3b 0x0007 0xFE
./i2c_write 10 0x3b 0x0010 0xDB
./i2c_write 10 0x3b 0x0011 0x9F
./i2c_write 10 0x3b 0x0012 0x00
./i2c_write 10 0x3b 0x0013 0x00
sleep 1
./i2c_read 10 0x3b 0x0014 1
./veye_mipi_i2c.sh -w -f paramsave

[veye_xumm]

@milank Okay, looking forward to the results of your test.

[milank]

@veye_xumm
Hello,
now, it seems that this additional line did the trick.
No brightness drop seen anymore.
Thank you for your help.

[veye_xumm]

@milank OK. You are welcome.