GX-MIPI-IMX662 can't save fps parameter

[alex_ai]

@veye_xumm found what was wrong,
high level of noise produced gamma_index = 1 (default value), other looks good.

[veye_xumm]

@alex_ai Thank you for your feedback; we will look into this issue.

[veye_xumm]

@alex_ai I used firmware version 1.14 for comparison and did not observe any significant noise changes in gamma mode 1 compared to other modes. Could you provide your specific usage parameters and environment?

[alex_ai]

Hi @veye_xumm, I didn't say that this is issue, this parameter needs to be changed only in case video recording of the night sky (meteor detection)

From issues what I noticed:

• can't save fps - always 60 after power on

• Sometimes saved parameters resets to default (noticed when set metime to 33333 but forgot set fps 30 before) and manual expmode switched back to auto

[alex_ai]

Hi @veye_xumm, I'm still trying to configure imx662 for night capturing (meteor detection) and probably you can help me to clarify what is wrong.

I have several cameras from VEYE (imx462 and imx462 mono) and also imx662 mono from another vendor.

And for all cameras configuration pretty same - use 30fps, exposure time 33333 and gain 30Db for mono version and up to 34Db color version (this range approximately within analog gain).

What I see in GX imx662 - for same parameters image too dark, some brightness I can get from gamma_index (with value 5 or 10) but it still not enough

To get required brightness of image I have to increase gain to 45 which leads to boost digital gain and as result more noise, more hot pixels and overbrighted (oversized) stars.

Questions:

1. What could be wrong? (imx662 mono works as expected, not sure it is sensor issue)
2. Can I read sensor registors same as on imx462?

My current config (Raspberry Pi 5, Trixie) :

./gx_mipi_i2c.sh -w fps 30 -b $i2cBus
./gx_mipi_i2c.sh -w expmode 0 -b $i2cBus
./gx_mipi_i2c.sh -w metime 33333 -b $i2cBus
./gx_mipi_i2c.sh -w mgain 34 -b $i2cBus
./gx_mipi_i2c.sh -w denoise_strength_3D 0 -b $i2cBus
./gx_mipi_i2c.sh -w denoise_strength_2D 0 -b $i2cBus
./gx_mipi_i2c.sh -w sharppen 30 -b $i2cBus
./gx_mipi_i2c.sh -w gamma_index 5 -b $i2cBus
./gx_mipi_i2c.sh -w daynightmode 1 -b $i2cBus

Example of image in same time and same parameters (gain 34) for:
GX IMX662

VEYE IMX462

[veye_xumm]

@alex_ai First, let me explain the gain configuration logic for the GX-MIPI-IMX662. The IMX662 features 30dB of Analog Gain and supports High Conversion Gain (HCG). The HCG function acts as an amplification during the sensor's analog signal readout, equivalent to 15.3dB.
Therefore, when we configure the "Again" parameter, the actual range is [0, 45.3dB]. This means you can set the Analog Gain up to 45dB without enabling Digital Gain (Dgain).
Currently, our firmware integrates HCG into the "Again" setting, which may have caused some confusion during your testing.
As for the feature to read sensor registers, I have added it to the development roadmap. It will be provided later via a firmware update package.

[veye_xumm]

@alex_ai

We recently updated the ISP tuning. Please give it a try.

https://wiki.veye.cc/index.php/GX-MIPI-IMX662_Version_Log

[alex_ai]

Hi @veye_xumm,
Thank you for new update and letting me know!

On first look - the original issue was fixed - now I can save fps parameter and we could close this topic.

About night sky image, I don't see visible differences and want to play with parameters one more time and monitor camera registers.

I see was added new feature:

./gx_mipi_i2c.sh -r snsreg [sensor reg addr] -b your_i2c_bus_number

I tried check sensor gain (register 0x3070) but not sure what should be reg address, tried 0x3070 and 0x70 (seems like it is expecting value less than 0x100)

if you could provide example - it would be helpful

Thanks

[veye_xumm]

@alex_ai
I would recommend using the exptime and curgain functions first to check the current performance of the camera module. If you are familiar with the sensor registers, you can verify the sensor's working status by reading registers 0x3070 and 0x3071.

[alex_ai]

@veye_xumm yes, I want to verify camera sensors but this command doesn't work for me, that is why I asked example.

 $ sudo ./gx_mipi_i2c.sh -r snsreg 0x3070 -b 6
 Read Sensor Reg 0x3070, val=0xffffffffffffffff

Unfortunately, my night sky tests failed:

• Without an IR filter, I can't get the stars into focus for some reason—they are always blurry and haloed.

• With an IR filter, the stars are in focus but they become extremely dim.

I'll probably stick with the old IMX462 sensor for my projects.

[veye_xumm]

@alex_ai

I'd like to first confirm your firmware version with you. As shown below, everything is working fine on my end.

pi@raspberrypi:~/gx_product_tool $ ./gx_mipi_i2c.sh -r snsreg 0x3070
Read Sensor Reg 0x3070, val=0x0 
pi@raspberrypi:~/gx_product_tool $ ./gx_mipi_i2c.sh -r snsreg 0x3071
Read Sensor Reg 0x3071, val=0x0 

pi@raspberrypi:~/gx_product_tool $ ./gx_mipi_i2c.sh -r version
Read version is C 01.32 and L 01.19

Regarding the image quality during IR-cut switching, may I ask whether you are using the same IR-cut filter for both the IMX662 and the IMX462? Also, could you share some sample images with me?