@nimadibaj

We are analyzing the output signal. It seems that between each video line, the CSI-2 output from your module enters Low-Power (LP) mode, which causes the video stream to continuously drop in and out. The module is completely new, and we have not sent any I²C commands to it. It appears that the module should operate in High-Speed (HS) mode, but it does not.

Hi,
What is the default config of veye mipi 462 ?

UYVU or YUYV ?
25 fps or 30 fps ?

HS mode and LP mode?

Thanks.

Hi,
I'm trying to config veye_mipi_imx462.
FPGA => IMX462 (via I2C)
I had extracted i2c command list from your script.
This is a part from my command list:
I2C_ADDR ==>> 0x3b
//=========================
read_devid :
read 0x3b 0x01
//=========================

read_releasedate :
write 0x3b 0x10 0xDA
write 0x3b 0x11 0x5C
write 0x3b 0x13 0x01
sleep 0.01
yy= read 0x3b 0x14

write 0x3b  0x10 0xDA
write 0x3b  0x11 0x5D
write 0x3b  0x13 0x01
sleep 0.01
mm= read 0x3b 0x14 );

write 0x3b  0x10 0xDA
write 0x3b  0x11 0x52
write 0x3b  0x13 0x01
sleep 0.01
dd= read 0x3b  0x14

//=========================
read_hardver :

hardver= read 0x3b  0x00

//=========================
read_sensorid :

sensorid_h= read 0x3b 0x20
sensorid_l= read 0x3b 0x21
SENSOR_ID=(((sensorid_h<<8)+sensorid_l))

//=========================
read_wdrmode :
write 0x3b 0x10 0xDB
write 0x3b 0x11 0x32
write 0x3b 0x13 0x01
sleep 0.01
wdrmode= read 0x3b 0x14

write_wdrmode :
write 0x3b 0x10 0xDB
write 0x3b 0x11 0x32
write 0x3b 0x12 $PARAM1
write 0x3b 0x13 0x00

value description
0x00 Back Light Mode OFF
0x01 Back Light Mode ON, LOW
0x02 Back Light Mode ON, HIGH
0x03 DOL WDR Enable
//=========================

But I just can read device ID, and None of the commands work.

Please guide me. Are the commands I wrote above wrong?

@veye_xumm
Thanks

Dear Sir/Madam,

We are working on VEYE-MIPI-IMX462 and trying to get the video with FPGA but we couldn't receive the video as YUVY4:2:2 8bit but we receive some noisy data as RGB Video.

1_What is the actual video format?
2_What is the pixel-per-clock rate?
3_What is the Line Rate of camera?
4_Is there a sample code for XILINX FPGA to receive VEYE-MIPI-IMX462 video output?

We would appreciate it if you could help us to receive the mentioned camera video output.

Best Regards,

@nimadibaj
In all file I can just see imx307 & 327 & CS & mv & in raspberry and Jetson DTS and ....
Why??
What is I2C address for veye imx462??

Hi,
I'm trying to control this cam module through I2C bus by a fpga.
But in first step, I can not detect it!
What is true Address of Veye imx462?
Thanks